https://wiki.we-measure.io/ 2026-04-17T12:16:43+00:00 https://wiki.we-measure.io/ https://wiki.we-measure.io/lib/exe/fetch.php/wiki/logo.png text/html 2026-04-15T14:12:49+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/account?rev=1776262369&do=diff Account Shows a list of useful links and open tasks (if any) <https://we-measure.io/user/profile> Wings * Lists all wings you added to your profile so far, ordered by purchase date (if added) * You can add or remove wings here * Details on wings can be updated by clicking on them text/html 2025-11-16T08:45:34+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/angle-of-incidence-view?rev=1763282734&do=diff Angle of incidence view For each section of lines (a section consists of main lines that are behind each other e.g. A1, B1, C1), we show the angle of incidence (AoI) compared to the nominal angle of incidence. To have your wing trimmed as close to the factory setting as possible, this line should ideally be straight and in the middle of the view with no angle. The dotted line indicates the manufacturer's tolerance as selected in the set-up (see above). A text/html 2025-11-17T17:04:57+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/comparison?rev=1763399097&do=diff Measurement comparison In the comparison view, you see the older measurement, symmetry and trim data in red and the newer data in blue. Here you can compare, how the changes on your trim have influenced the relative angle of incidence (AoI) and symmtery between two measurements. text/html 2025-11-15T17:42:16+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/connecting-the-laser?rev=1763228536&do=diff Connecting the laser Make sure your laser device is switched on. Click the button­ and select your laser device from the dialog. For questions regarding supported devices, you can check our FAQ. text/html 2025-11-16T20:35:03+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/finish-dialog?rev=1763325303&do=diff Finish dialog Once you are finished with simulation and/or trimming, you can proceed via clicking the ­ button the “Finish measurement” dialog will be shown. First you can add a comment to your measurement and select if both, measurement and comment, should be published anonymousely to the text/html 2026-04-15T14:21:26+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/loops?rev=1776262886&do=diff Loops In the following overview you'll find a set of loops that can be done to adjust the trim of a paraglider. Open Single Loop Girth Hitch Wikipedia Double Loop Girth Hitch Plus Pile Hitch Wikipedia Girth Hitch Plus Plus Pile Hitch Plus Double Pile Hitch text/html 2025-11-14T11:02:58+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/measurement-import?rev=1763118178&do=diff Measurement import For users without a supported laser device or for measurement reports received from a check-center, we implemented an option to import measurements from an xlsx file by using the import­ feature. You can either select that you want to text/html 2026-03-16T13:56:12+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/measurement-overview?rev=1773669372&do=diff Measurement overview Start a measurement To start a measurement, you first have to enter some information rearding the wing's current status. "Started" You can continue a measurement where you've left of to entere missing readings after taking a break. If the measurement to continue is older than three days, you will be forwarded into the wizard for starting a measurement, just to make sure all the information is still up to date. text/html 2025-11-15T07:12:49+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/measurement-settings?rev=1763190769&do=diff Measurement settings With the ­button you can avoid having to push the button on your laser twice in order to get a value. This will automatically switch the laser on after each reading. Make sure that you do not point the laser at people. When ­ is switched on, the application will automatically discard values that are considered implausible (away from the expected value by more than 4x of the manufacturer's tolerance). text/html 2025-11-17T07:14:36+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/measurement-setup?rev=1763363676&do=diff Measurement setup First of all, make sure that your laser device is supported. You can test here if connection is working. If this is not the case, please contact us and we will see, if we can add it. For details on supported devices please check our FAQ. text/html 2025-11-12T17:14:11+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/measurement-view-and-plausibility-check?rev=1762967651&do=diff Measurement view and plausibility check In the measurement view, the group of lines where you're currently at is highlighted in the wing in red and magnified. By this, you can see exactly the values of your last readings, even if using a smartphone to run this application. text/html 2025-11-11T18:08:17+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/offset-of-measurement-setup?rev=1762884497&do=diff Offset of measurement setup Every measurement setup is a bit different. If you did not yet setup the offset in your profile settings, you can do it prior to starting your measurement below the section where you entered your loops. The offset does not affect imported values or measurements that are in simulation or finished. It only there to add/subtract the given value from the reading of a connected laser. text/html 2026-03-16T13:53:57+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/re-measure?rev=1773669237&do=diff Re-measure In case you selected, that you would like to re-measure the wing, you can then select, which readings should be re-set. If only single main lines are selected here, for all other main lines and their accompanying suspension points, the readings will be copied from the measurement before. text/html 2025-11-16T09:01:21+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/referencing-different-lines?rev=1763283681&do=diff Referencing different lines Main line as reference Aside from the standard view in simulation view, you can select between three different references to get the full picture of your wing. The first type is referencing on the main lines. This can be achieved by either clicking the name of the main line in the wing view or by checking the radio button next to the name of the desired main line in the value view below. text/html 2026-04-15T05:25:54+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/registration?rev=1776230754&do=diff Registration In order to use our application for measuring your wing, you need to register with us. registration formconfirmation link via emailbefore trying to login text/html 2025-11-16T20:17:15+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/result?rev=1763324235&do=diff Result The result view offers you different operations that you can perform with the gained data. Per default you see the data of your just finished measurement in the AoI view. The toggle button allows you to switch between AoI view and Symmetry view. By this you can easily see full effects on your trim. text/html 2025-11-16T09:06:11+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/simulating-trim-changes?rev=1763283971&do=diff Simulating trim changes Finally, in the simulation you can get a rough estimation about how loop changes on the main lines of your wing affect the AoI and symmetry of your wing. You can select the various loop options by clicking on them to see how the AoI in this section of your wing or the symmerty might be affected. text/html 2025-11-16T08:46:21+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/simulation-overview?rev=1763282781&do=diff Simulation overview In the simulation window, the following elements can be found: Since in the simulation you are also able to check how changes in the loops will affect the trim of your wing in terms of angle of incidence and symmetry, will reset all the loop changes you did during simulation to how it was set up before measurement. text/html 2026-04-15T14:16:00+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/start-measurement-wing-status?rev=1776262560&do=diff Start measurement - Wing status When you start a new measurement, you first will be forwarded to a page for entering your wing status prior to starting the actual measurement. We here provide the possibility to verify that the used values for the linemap is correct. Although, we thoroughly take care to enter everything correctly, we can not guarantee that there are no mistakes. Manufacturers might update their linemaps from time to time or may even provide incomplete information. text/html 2025-11-12T17:38:26+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/stop-mode-and-re-reading-of-single-lines?rev=1762969106&do=diff Stop mode and re-reading of single lines When you are in stop mode, make sure that you also hit the save button, if you take a longer break. However, every reading taken by a connected laser is also saved on the server immediately. When pushing the start button again, measurement will continue where you've left off (the first empty field is selected automatically). text/html 2025-11-16T08:52:38+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/symmetry-view?rev=1763283158&do=diff Symmetry view With the symmetry view we help you even more, to keep your wing in a good shape. In the Simulation and in the Result view you can switch between the normal AoI overview and the symmetry view by toggling the respective button. To satisfy the requirements for relative trimming, the median of all differences to the nominal value is calculated. The symmetry deviations are then shown relative to this median. text/html 2025-11-23T19:05:41+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/toolbar?rev=1763924741&do=diff Toolbar Pages showing measurements of any status or measurement comparisons always have toolbar on top with different controls and/or actions regarding to the current status. green “” AoI viewsymmetry view text/html 2025-11-11T17:41:21+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/wing-information?rev=1762882881&do=diff Wing information By clicking on already existing wings in your collection you will see detailed information. In the Info dialogue, you can change the description and add information that in the About field are displayed as n/a. The description can be a color, nickname or whatever you like to enter there. It will be displayed in brakets behind the wing type instead of the default date of certification for this wing. text/html 2026-04-15T14:14:14+00:00 Anonymous (anonymous@undisclosed.example.com) https://wiki.we-measure.io/doku.php/en/workflow?rev=1776262454&do=diff Workflow In general, measurements can have three diffferent states: * Open * Simulation * Finished So you decided to measure your wing's line lengths, as since the last trim check * the number of flight hours specified by the manufacturer has been reached